Drive Control Of Stepping Motor In CNC Machine Tool Factory


1. The working method of stepper motor in CNC machine tool factory

Switching from one phase to another is called a beat, and the rotor rotates by a step angle for each beat. Press A_. ¨c_A-… When the power is supplied in the sequence, the rotor of the motor will rotate step by step in this order; on the contrary, if the power is supplied in the order of A-cB÷A-…, the motor will rotate in the reverse direction. The mode of sub-single-phase energization’ is called three-phase Zi three-beat A operation t “single” means that only one phase winding is energized at a time. Three beats. It refers to three times in a cycle, that is, ABC three beats. In the single-three-beat power-on mode, only one phase of the control winding is energized to attract the rotor at a time, which is easy to cause the rotor to oscillate near the equilibrium position, and the running stability is poor; Power-on, it is easy to cause out of step, so it is rarely used in practice – this power-on method is mostly three-phase double-three-beat method.

The three-t double-beat mode means that the power-on mode is AB-BC-CA_AB_… sequence, and two-phase windings are powered on at the same time each time. This energization method has large induction torque, small static error and high positioning accuracy. In addition, there is always a phase control winding energized when the energization state is switched, and the motor works stably and is not easy to lose steps.

Three-phase six-beat power-on mode, that is, the power-on sequence is A-AB-B-BC_c-cA-A-A…, this power-on mode is single-phase and two-phase alternating current, with the characteristics of double two-beat, and the power-on state is doubled, Decrease the step angle by 1.

2.Control System of Stepping Motor in CNC Machine Tool Factory

Diagram of the stepper motor drive control system of the CNC machine tool factory. It is composed of a pulse mixing circuit, an addition and subtraction pulse distribution circuit, an acceleration and deceleration circuit, a ring distributor and a power amplifier. The pulse mixing circuit, the addition and subtraction pulse distribution circuit, the acceleration and deceleration circuit and the ring distributor can be realized by hardware circuits. Software can be used to achieve.

(1) Pulse hybrid circuit

Whether it is the interpolation signal from the CNC system, or various types of error compensation signals, manual feed signals and manual return-to-origin signals, the purpose is to make the table feed forward or backward. First of all, these signals must be mixed into a “forward feed” signal that makes the workbench feed forward or a “reverse feed” signal that makes the workbench feed backward, and the pulse mixing circuit implements this function.

(2) Addition and subtraction pulse distribution circuit

CNC machine tool factory When the machine tool is feeding in a certain direction under the control of the feed pulse, due to the existence of various compensation pulses, there will also be very individual reverse feed pulses, which are different from the feeding pulses. The appearance of individual pulse commands in the opposite direction means that when the actuator, that is, the stepping motor, is rotating in one direction, it rotates in the opposite direction by a few step angles. The general method is to start from the feeding direction. The same number of reverse compensation pulses are offset in the feed pulse command, which is also the function of the addition and subtraction pulse distribution circuit.

(3) Acceleration and deceleration circuit of CNC machine tool factory

The acceleration and deceleration circuit is called the automatic acceleration and deceleration circuit. According to the acceleration and deceleration characteristics of the stepping motor, the frequency change of the level signal entering the stator winding of the stepping motor should be smooth, and there should be a certain time constant. However, since the feed pulse frequency from the addition and subtraction pulse distribution circuit has a jump, in order to ensure that the stepper motor can work normally and reliably, the jump frequency must first be buffered to make it conform to the stepper motor. Acceleration = deceleration special pulse frequency, and then sent to the stator winding of the stepping motor, the acceleration and deceleration circuit is set up for this purpose.

The structure principle of the acceleration and deceleration circuit is shown in Figure 4.7. It consists of a synchronizer, an up and down counter, a digital-to-analog conversion circuit and an RC variable frequency oscillator. The function of the synchronizer is to prevent the feed pulse ^ and the pulse fh from the RC variable frequency oscillator from appearing at the same time, so as to prevent ^ and ^ from entering the reversible counter at the same time, so that the reversible counter does both addition and subtraction at the same time. A count error occurred. The function of the RC variable frequency oscillator is to convert the voltage signal input by the digital-to-analog converter into a pulse signal, and the frequency of the pulse is proportional to the size of the teleporter. The function j of the digital-to-analog conversion circuit is to convert the digital quantity into the analog quantity.

(4) Ring distributor of CNC machine tool factory

The function of the ring distributor in the CNC machine tool factory is to convert a series of feed pulse commands from the acceleration and deceleration circuit into a level signal that controls the power on and off of the stator winding of the stepping motor. The number and direction of the feed pulses correspond. For example, for a three-phase single-three-beat stepper motor, if “l” means power-on, “.” means power-off, A, B, and c are its three-phase stator windings. After the distributor, A, B, C should be changed in the order of (100) one (010) one (001) one (100)… for each feed pulse command.

There are two types of ring distributors: hardware ring distributor and software ring distributor. The hardware ring distributor is a hardware logic circuit composed of flip-flops and f]circuits. Now there are PM()S and CM()S ring distributor chips with high integration and strong anti-interference on the market for selection, and software ring distributors that can realize pulse sequence distribution by computer software.

(5) Power amplifier

The power amplifier fork is called power driver or power amplifier circuit. The current of the feed control signal from the ring distributor from the CNC machine tool factory is only a few milliamperes, while the stator winding of the stepper motor needs a current of 100 amps. Therefore, a power amplifier is required to amplify the pulse current from the ring distributor enough to drive The stepper motor rotates.
The power amplifiers used in stepping motors are of current type and voltage type. The current type of CNC machine tool factory includes constant current drive type, chopper arrogance type, etc.; voltage split has single voltage type and dual voltage type (high and low voltage type).

 


At Be-cu.com,we use advanced equipment to offer you Unparalleled precision for producing metal and plastic machining parts

  • We combine the latest CNC milling and turning processes with proprietary technology to deliver high quality, on-demand parts.
  • Our team of engineers and machinists program the equipment to optimize cutting time, surface finish, and final tolerance to meet your design specifications
  • We specialize in cnc precision machining, single part prototyping, short to medium production runs, manufacture parts on time, every time, so you can stay ahead of schedule
  • CNC machining can create very similar parts to series parts. It is often more efficient and faster than other rapid prototyping technologies for the manufacture of a quantity of prototypes between 1 and 10 parts . We also recommend CNC machining for parts with large sizes (greater than 600 mm).